Eastwood Blast Cabinet Foot Pedal and Gun

Eastwood Blast Cabinet Foot Pedal and Gun kit is designed to replace the standard trigger operated blast gun.

Eastwood Blast Cabinet Foot Pedal and Gun - EW21133

Eastwood Blast Cabinet Foot Pedal and Gun kit is designed to replace the standard trigger operated blast gun.

• Eliminates hand fatigue
• Gives more precise media flow
• Replaces trigger operated guns
• Includes High-Volume Blast Gun

The Foot Pedal eliminates hand fatigue and adds more precise control to the blast media flow. This kit enable you to blast for longer periods of time without having to take breaks due to hand fatigue.

Contents:
(1) High-Volume Blast Gun with Air Supply and Media Pick-Up Hoses
(1) Foot Pedal Control with Air Supply Hose and Bulkhead Fitting

Specifications
Minimum air requirement: 7.1 CFM @ 90 PSI
Optimum operation requirements: 10.25 CFM @ 115PSI
Maximum operating pressure: 120 PSI
6mm Nozzle

Application

CLEAN - Thoroughly strip and clean your metal part before coating. We recommend Eastwood Pre Painting Prep.

COAT - Apply using Eastwood DIY HotCoat Gun 11671A or the Eastwood Dual Voltage HotCoat Gun 11678.

CURE - Cure the part in an electric oven for recommended time. NEVER use an oven that is used for food.

Specification

Safety

WARNING: Blasting emits abrasive under pressure. Adequate respiratory eye and body protection must be worn during use. Inhalation of silica based media particles have been known to cause cancer and other deadly diseases, and must be avoided. Wear NIOSH approved respiratory protection while operating this equipment.

MSDS

PRODUCT INFORMATION
msds Click for Material Safety Data Sheet

The information contained herein is based on data considered accurate and reliable to the best of our knowledge and belief as of the date compiled. However no warranty is expressed or implied regarding the accuracy of these data or the results to be obtained from the use hereof.

Blast Cabinet Foot Pedal & Gun Upgrade - Blast Away Rust & Paints With Ease!

  • Great price
    Got this a couple months ago for my Harbor Freight cabinet . It’s easy to hookup and blasted better then the original. I had to buy a couple different media before I found the one that worked right . The hose going to the sand needs to be replaced with a better one . I got mine at the local hardware. You should get a couple nozzle ends also . Other that that all is good.
  • Easy install and easy to use
    I got this with two other up grades for a harbor freight blast cabinet could it be more happy
  • Simple and tough
    Purchased a month ago and hooked it up to my 10 year old harbor freight blast cabinet. Works perfect and helps get the job done fast. My wife loves beadblasting my parts now. Thanks Eastwood for a quality part at a reasonable price. May have to order a back-up so I will never be without. I have a 10 hp compressor so air is no problem.
  • Easy to install works great
    Bought this to replace the one that came with my blast cabinet should have bought it sooner man what I differences
  • A must for any blast cabinent
    I will admit, I bought a "discount tool stores" blast cabinet. The blast guns performance was horrible at best. I picked this up from the local Eastwood Store (I am lucky enough to have one 10 minutes from my house!) as they are out of stock online. I hooked it up and took it for a spin. A part that would take an hour previously I had done in less than 10 minutes and with better results.
    If you have Eastwood's cabinet or some other "discount tool store" version, spend the $60 on this upgrade.
  • Nice product
    Easy to order fast shipping everything needed to install
  • Great Gun and Pedal Kit
    Bought to upgrade my Harbor Freight blast cabinet. Gun and pedal work awesome. At this point I have only used aluminum oxide as the blast media. My setup includes using an 80 gallon, 2 stage compressor, which I’m sure greatly helps with performance. Orverall great kit for the price.

Write a Review

1    2    3    4    5
Name *
Email *
Phone *
Product Name
Comment *