Eastwood HotCoat Powder - Metallic Purple

The Rust Restoration Specialists !

Eastwood Hotcoat Powder Metallic Purple

Extremely durable, chip-resistant finish; coat and cure in under an hour.

Size: 1 lb Bag

Product Code: EW11818LB

Quantity

Check out our Product Guide for Common Uses for PPC CO. Products on restoration projects.


ppcco tabs

Eastwood Hotcoat Powder Metallic Purple - EW11818LB

Do The Job Right with Eastwood Powders!

▶   Provides extremely durable finish
▶   Contains no environmentally harmful solvents
▶   100% Virgin powder
▶   Impact resistant and flexibility
▶   Good chemical resistance

Eastwood Powders are far superior to liquid coatings. They provide an extremely durable finish that is chip resistant. All Powders are formulated of the highest quality materials and are chemical and fuel resistant. Eastwood Powders are durable enough for under hood applications and heat resistant up to 250℉. They are suitable for any metal surface and most cure at a temperature of 400℉ at 20 minutes after flow out. With Eastwood powders, you can be assured of high transfer efficiency and brilliant colors.

Metallic Purple Powder HotCoat Single Stage Starlight Powder - This one step powder produces a deep, pleasing medium Purple high gloss finish with special fine metallic sparkle flakes.

Application

CLEAN - Thoroughly strip and clean your metal part before coating. We recommend Eastwood Pre Painting Prep.

COAT - Apply using Eastwood DIY HotCoat Gun 11671A or the Eastwood Dual Voltage HotCoat Gun 11678.

CURE - Cure the part in an electric oven for recommended time. NEVER use an oven that is used for food.

Specification

Color: Metallic Purple
Gloss Level: Gloss
Cure Temperature: 400℉
Cure Time: 20 Minutes after flowout
Powder Type: Urethane
Finish: Smooth
Coverage: 1/2 lb. of powder is approximately 10-20 sq. ft.

Safety

When applying powder always apply it in a well ventilated area away from heat sparks and open flame. Always use a respirator rated for dust while applying powder. Always store powders in cool (less than 80 degrees Fahrenheit) dry (60 percent or less humidity) well ventilated area away from heat sparks and open flame.

Other Colours

Select Powder Range to see

map
map

Powder Coating Made Easy - Dual Voltage Powder Coating Gun from Eastwood

With our dual-voltage HotCoat gun, you can powder coat interiors and hard-to-reach corners using the low 15,000-volt setting, or switch to the high 25,000-volt setting for multi-coat coverage over larger areas with increased powder adhesion and minimal overspray. Either way, you'll get all the benefits of powder coating in your own shop!

Extremely durable finish
Coat and cure in under an hour!
Easy to apply
Quick color changes
Economical

  • Oven bake vs. propane burner
    This purple is HOT! Strange experience for me when baking. I used my oven for the small parts and my propane heater for the large parts. The flakes using propane baking method really popped! The oven baked parts were not so dynamic. Thinking I may have changed something in my process I stripped the parts and did it all over again (They obviously needed to be uniform in color) and I had the same results. So I stripped the small parts once more and propane baked them!
    When painting with old style heavy flake enamels you could change the flakes effects with higher or lower air pressure and spraying style. I attempted this with this product but not sure it changes so much.
  • awesome
    if you want to knock one out of the park this color will do the trick, did my motorcycle man does it pop it the sun, AWESOME
  • Good Coverage
    I am shooting this powder on pulleys, intake manifold, etc. for a chevy small block and I am satisfied with the coverage. I was hoping the purple would cure out very dark and it did, but the metallic is not as extreme as I was hoping it would be. It has a sparkle, just not enough to make it a focal point. Good powder, just not my favorite.